SBC cPCI  

CPC510

Solution provider for Embedded and Industrial PC

CPC510

SBC EMBEDDED

Intel i7-3517UE/i7-3555LE, DDR3 SDRAM 1333/1600Mhz, DDR3L SDRAM 1066Mhz up to 8 GB, 2 LAN, 13 USB 2.0, 4 USB 3.0



General Features

– Intel i7-3555LE/i7-3517UE
– DDR3 SDRAM 1333/1600Mhz, DDR3L SDRAM 1066Mhz up to 8 GB
– 2 LAN, 13 USB 2.0, 4 USB 3.0

Technical Features
Intel IvyBridge CPU (2/4 Cores) Intel i73517UE (DC, 2C/4T, 1,7 GHz, 1600 MHz, 4 MB, 17 W)
Intel i73555LE (DC, 2C/4T, 2,5 GHz, 1600 MHz, 4 MB, 25 W)
Panther Point PCH
Memory DDR3 SDRAM 1333, 1600 Mhz or DDR3L SDRAM 1066, 1333 Mhz with ECC up to 8 GB soldered, dualchannel
Video Output (simultaneous output to 3 monitors) Two DisplayPort connectors (resolution up to 2560 × 1600@60Hz) at the front panel
DisplayPort interface (resolution up to 2560 × 1600@60Hz) is routed to the mezzanine module
LPC Bus To the mezzanine connector
PCIE Bus
CPU Hosts. PCIE 2.0 support (up to 5GT/s):
Output via the PCIE switch to J1 and J2 CPCI Serial connectors with support for two x8 FatPipe#1 and FatPipe#2 devices
Support for the Non-Transparent mode for FatPipe#1
Output via the PCIE switch to J4 CPCI Serial connector with support for four x4 devices.
PCH Hosts. PCIE 2.0 support (up to 5GT/s):
Output to the mezzanine module on the left
MIC590 connection.
SMBUS Bus Compatibility with the 2.0 specification
Speed up to 100 kbps
FLASH BIOS 64 Mbit SPIFlash
MicroSD Interface
Support for the SDHC 2.0 specification
Connected to a USB 2.0 interface
SATA II Interface One interface is always routed to the mezzanine connector:
One interface  is switched between J3 CPCI Serial connector and the mezzanine connector
Two ports are routed to the J3 CPCI Serial connector.
SATA III Interface Two interfaces are routed to the J3 CPCI Serial connector
Support for RAID 0, 1, 5, 10
2 ports LAN 10/100/1000 Mbit at PCIE x4 Gen2 Two interfaces are routed to the XS5 connector at the front panel
Implementation of a server network adapter
USB ports 13 USB 1.1 ports (12 Mb/sec), USB 2.0 (480 Mb/sec) and 4 USB 3.0 ports (4.8 Gb/sec)
Two USB2.0 ports are routed to connectors at the front panel
Two USB2.0 ports are routed to the mezzanine connector
8/4 USB2.0 ports are routed to the J3 CPCI Serial connector*
1 USB2.0 port is used for implementation of the MicroSD interface
4 USB3.0 ports are routed to the J1 and J2 CPCI Serial connectors*
FRAM Memory 32 Kbyte, RAM 1 Kbyte for storing settings of the Bios Setup
Implemented on the SPI Bus
Real time clock (RTC) Power is supplied from a CR 2032 lithium battery (3V)
Audio Support HD Audio interface is routed to the mezzanine connector
Watch dog timer Internal with a possibility of programmed control
SGPIO Interface Support for signaling according to the SFF8485 Specification
Hardware monitor Implemented via PECI/SMBUS interfaces
Monitoring of three supply voltages
Monitoring of the CPU temperature
Monitoring of the PCB temperature
Monitoring of the RAM temperature
Support for the power source management Indication Board Startup Diagnostics LED / Hot Swapping Light.SATA/SD Drives Access LED
Two softwarecontrolled LEDs (userdefined)
Temperature state LED
PCI Express Interconnections state LED
OS Programming Compatibility Windows 7 Embedded
Linux 2.6
QNX 6.5
Power Requirements Power voltage +12V, +5V_STBY (option)
Operating temperature range Industrial Modification: from –40°C to +85°C
Commercial Modification: from 0°C to +70°C
Humidity Up to 80% noncondensing
Vibration / Single shock resistance 5g/100g
MTBF Not less than 100,000 hours

Contact us for more information about cPCI CPC510